The microorganism and parasite can be killed in the process of extrusion. When using, it should be noted that there should be no foreign matter such as stones and iron blocks in the raw materials. After the pellet machine has been working continuously for more than ten shifts, the pressure roller oil hole, the universal joint oil hole, and the linkage shaft oil hole need to be filled with high-temperature lubricating grease to make the pressure roller have good working performance and extended bearing life.
3 Roller Farm Animal Feed Pelletizer 2/4/8mm Plate Feed Pellet Mill Machine 220V Note: 1. Before using the machine, it is necessary to adjust the screw of the pressure roller to the appropriate position. The pressure roller and the pressure plate should be closely combined, and the three adjusting screws should be on the same horizontal plane. 2. Please refuel the fuel tank before using the machine. The machine should not idle for more than 2 minutes. 3.Double-check the belt and the screws before operation. 4.Clean up the rest after use to prevent damage to the machine. 5.If the pressure roller cannot rotate normally, please tighten the screws that control the pressure roller first, and then try to power it on. If it still does not work, you can appropriately loosen the screws next to the pressure roller and then tighten them slightly again (without special tightening) Plate: 2MM,4MM,8MM Output/h 120-150KG power: 4.5KW voltage: 220V Product body material: cast iron Standard pressure roller: Three head press roller Product size: 32.67*12.99*30.18in(83*33*76.5cm) Feature: This machine is equipped with an enlarged and widened discharge port to prevent feed splashing and facilitate the collection of feed by customers. This machine is equipped with a voltage display, which can visually see whether the voltage is stable. Adjustable nut Used to adjust the distance between the pressure roller and the grinding disc. When making pellets, the nuts on the three sides must be balanced to avoid damage to the pressure roller and grinding disc. If the pressure roller cannot rotate normally, please tighten the screws that control the pressure roller first, and then try to power it on. If it still does not work, you can appropriately loosen the screws next to the pressure roller and then tighten them slightly again (without special tightening) Enlarge the feed inlet The machine adopts the design of enlarged feed port, which makes it more convenient for you to feed and effectively improves work efficiency. Here is the filling port, open here to add engine oil It is recommended to add high-quality machine oil or hyperbola heavy-duty gear oil. The length of feed particlescan be adjusted here. The machine is equipped with air switch, which is safer to use. Nylon wheels are adopted, which are more wear-resistant and durable. After using the machine for a period of time, the customer needs to add butter to lubricate the grinding chamber here (approximately 4-6 months of use) (the butter gun and butter need to be purchased by the customer themselves, and we do not provide them). Precautions: 1.When using, it should be noted that there should be no foreign matter such as stones and ironblocks in the raw materials. After the pellet machine has been working continuously for morethan ten shifts, the pressure roller oil hole, the universal joint oil hole, and the linkage shaft oilhole need to be filled with high-temperature lubricating grease to make the pressure roller Goodworking performance and extended bearing life. 2.During granulation, it is strictly forbidden for the pressure roller to contact with the templateto run idly, and the continuous feeding can not be interrupted.At the same time, the pressureroller shaft nut is locked to avoid loosening and damaging the spindle keyway. 3.When granulating, there is no granulation, no discharge, the template should be removed, andafter opening one by one, some fiber feed can be added appropriately to restart the granulation. 4.Always check the tightness of the screws in each part of the machine. If there is oil leakage inthe gearbox, replace the oil seals in time, and check whether the bearings in the machine headare short of oil. 5.When the pellet machine is working, do not reach into the feeding port with your hands. Ifnecessary, use wooden sticks to help feed the pellets. 6.Before turning on the machine, it is necessary to add less material before turning on the machine. When shutting down, leave a small amount of feed in the machine to prevent the pressroller of the machine from contacting the template from idling. 7.If the machine is stuck in operation, stop it immediately, press the pressure roller until thebolt is flat,and then restart the machine. 8.Each time the work is completed, the adjusting pressure roller bolts must be loosened. 9.Iron or stones cannot be put into the griller. 10.Check the elasticity of the belt, and the bearing frequently. Add oil in time when it needs to. Note: We suggest that high-power machines should be directly connected to the main power supply, as the voltage reaching the machine is stable. If the voltage is unstable and the current exceeds the rated current of the motor, it is easy to burn out the starting capacitor. It is recommended to directly connect to the power supply as much as possible. If the machine is not connected to the power supply, different situations may occur, and the wires are not durable. The wires will gradually burn out over time. Our machine is not equipped with a plug. If you do not know how to operate the wiring video, you can contact our customer service and we will provide you with the wiring video. (If there are occasional situations with plugs, it is also recommended that you remove the plugs when wiring) Item Number: 1*Animal Feed Pellet Mill Machine 220V (239175+239553+239550) Shipping & Handling Details Default Shipping Cost or Free Shipping Information: ▲ Default shipping cost or free shipping service is only for the lower 48 United States by UPS Ground or USPS. Other areas or needs other shipping ways, please contact us. ▲ Buyers from Guam, Puerto Rico, Virgin Islands, American Samoa, Alaska, Hawaii, PO Boxes, APO/FPO addresses or other countries/areas, there WILL be extra shipping costs, please contact us for more detailed information. ▲ Please make sure your address is valid for both UPS and USPS services. Any costs incurred because of incorrect or undeliverable address should be undertaken by buyer. HandlingTime: Shipping is usually made in 1-3 business days after payments cleared. Orders are processed from Monday-Friday; Not on the weekends & public holidays. Sales tax/Customs duties: Any sales taxes or Customs duties are not included. If came out, they must be undertaken by the buyer. Damage In Shipping: Email or call us First! We will work with you to get the case resolved in the fastest method. Return / Refund If you are not 100% happy with your purchase, please contact Us. Please don’t directly opened a request or case without informing us, or else, we will do some discounts on the warranty and other sales-services later on. Hope for your understanding. Returns & Exchanges ▲ All returns must be made within 30 days of delivery date. Items must be in new, unused condition, with all original materials included with the shipment. A partial refund may be applied for opened or damaged items, depending on the condition. ▲ Items returned under the buyer’s remorse: The return shipping fee must be covered by the buyer; The original shipping cost will also be deducted from the refund. 15% restocking fee of the items purchase price will be charged. ▲ Returns that are the result of our seller’s error: Buyer will receive a full refund of the item as well as shipping charges ▲ All returns require a RA (Return Authorization) number that will be given by our seller. Please contact with us at first for more details. Defective & Damaged Products ▲ If product was received damaged or not as described, please send us some pictures or videos, so we could well understand your problem, then solve them for you ASAP. Besides, it’s much helpful for us to claim with UPS, remind our related department to pay much more attention to packaging later on. Hope for your understanding. ▲ Replacement or refund of defective or damaged products can only be returned in exchange for the exact same product, or else, the purchase price will be refunded back to your original payment method. ▲ If an item is received damaged, customer service must be contacted within 7 days of receiving your item. All returns require a RA (Return Authorization) number as above. Warranty & Feedback ▲ 6 months’ warranty for the machines, not for the consumables. We stand behind our products all the item, so even if your warranty period has expired, you can still seek for service or technical support from us with low cost. ▲ Any warranty shipping cost to us is responsible by buyer. ▲ Any shipping cost to buyer is responsible by the seller. ▲ We committee to the customer satisfaction and want to bring you the best purchase experience. If there is any problems, please contact us ASAP. If not, please leave us a positive feedback as it’s very important for us. Thanks very much. On Oct 28, 2024 at 22:51:25 PDT, seller added the following information:
新建网页 1 Dry-Wet Straw Hay Cutter Crusher Grain Grinder with Conveyor&Dust Collector 220V Dual use, dry and wet, not jammed, not tangled with grass Performance characteristics: This machine adopts chain automatic feeding and is suitable for cutting and kneading crops such as grass, corn stalks, sorghum stalks, wheat straw, rice straw, straw, etc. The cutting and kneading process can be adjusted in length. The hard stem nodes on the surface of the straw are destroyed through the cutting and kneading process, and the processed feed becomes soft and filamentous without hard nodes. This improves the taste of livestock and poultry ingredients such as cows, sheep, chickens, pigs, geese, rabbits, and improves the feed utilization efficiency of livestock and poultry, It is a necessary straw kneading mechanical equipment for farmers and small and medium-sized feed processing factories. Parameter: Shakelon dust collector, dust-free operation, improves working environment. The discharge port can be adjusted to adjust the discharge size as required. Adjustable gear, convenient and fast. Integrated molding fan, the working diameter is larger, the wind is larger. Thickened galvanized conveyor chain, automatic feeding, safe and efficient, dry and wet dual use. The feed port for grains is provided with a splash damper Cyclone Crescent knife set, grain pulverized, fast and fine. 6 Knife high hardness blade, 9CrSi hardness: HRC55 degrees, easy to cut, high efficiency. Adjustable feed port to control feed speed at any time. Feeding pressure roller, automatic feeding, convenient and fast. Accessory: Precautions: 1.Before using this machine, it is necessary to conduct a comprehensive inspection and adjustment to ensure that all connections are secure and reliable, and all rotating parts must be filled with lubricating oil. 2.Before starting the motor, jog it first to check for any abnormal collision sounds. At the same time, observe whether the rotor direction is consistent with the arrow direction marked on the body. Then, start the machine and idle for 5-10 minutes, and wait until everything is normal before feeding and working normally. 3.Apply lubricating grease evenly to the rotating gears and transmission chain wheels every 12 hours of operation, and apply grease to each operating part of the machine every 24 hours of operation. 4.When the work is about to stop, the machine should idle for 3-5 minutes to remove any remaining materials from the body. After cleaning the machine, lubricate and maintain all rotating parts. Warn Single-phase motor current is relatively large, 3 kw motor please use more than 4 square copper wire, wiring must be firm, it is recommended to use 63 Ann air switch, please do not use ordinary plug socket, so as not to current enough to lead to capacitor or motor burn out! (Please strictly follow the above tips!) Item Number: Farm Home Straw And Fodder Crusher 145037 Shipping & Handling Details Default Shipping Cost or Free Shipping Information: ▲ Default shipping cost or free shipping service is only for the customers from Canada or the lower 48 United States by Canada Post, USPS or the UPS Ground. Customers from other areas or needs other shipping ways, please contact us. ▲ Buyers from Guam, Puerto Rico, Virgin Islands, American Samoa, Alaska, Hawaii, PO Boxes, APO/FPO addresses or other countries/areas, there will be extra shipping costs, please contact us for more detailed information. ▲ Please make sure your address is valid for both UPS and USPS services. Any costs incurred because of incorrect or undeliverable address should be undertaken by buyer. Handling Time: Shipping is usually made in 1-3 business days after payments cleared. Orders are processed from Monday-Friday; Not on the weekends & public holidays. Sales tax / Customs duties: Any sales taxes or Customs duties are not included. If came out, they must be undertaken by the buyer. Damage In Shipping: Email or call us First! We will work with you to get the case resolved in the fastest method. Return / Refund If you are not 100% happy with your purchase, please contact Us. Please don’t directly opened a request or case without informing us, or else, we will do some discounts on the warranty and other sales-services later on. Hope for your understanding. Returns & Exchanges ▲ All returns must be made within 14 days of delivery date. Items must be in new, unused condition, with all original materials included with the shipment. A partial refund may be applied for opened or damaged items, depending on the condition. ▲ Items returned under the buyer’s remorse: The return shipping fee must be covered by the buyer; The original shipping cost will also be deducted from the refund. 15% restocking fee of the items purchase price will be charged. ▲ Returns that are the result of our seller’s error: Buyer will receive a full refund of the item as well as shipping charges ▲ All returns require a RA (Return Authorization) number that will be given by our seller. Please contact with us at first for more details. Defective & Damaged Products ▲ If product was received damaged or not as described, please send us some pictures or videos, so we could well understand your problem, then solve them for you ASAP. Besides, it’s much helpful for us to claim with UPS, remind our related department to pay much more attention to packaging later on. Hope for your understanding. ▲ Replacement or refund of defective or damaged products can only be returned in exchange for the exact same product, or else, the purchase price will be refunded back to your original payment method. ▲ If an item is received damaged, customer service must be contacted within 7 days of receiving your item. All returns require a RA (Return Authorization) number as above. Warranty & Feedback ▲ 6 months’ warranty for the machines, not for the consumables. We stand behind our products all the item, so even if your warranty period has expired, you can still seek for service or technical support from us with low cost. ▲ Any warranty shipping cost to us is responsible by buyer. ▲ Any shipping cost to buyer is responsible by the seller. ▲ We committee to the customer satisfaction and want to bring you the best purchase experience. If there is any problems, please contact us ASAP. If not, please leave us a positive feedback as it’s very important for us. Thanks very much. 新建网页 1 On Jul 2, 2024 at 03:21:11 PDT, seller added the following information:
Adjust the pressure rollers. Before grinding and feeding, be sure to check whether two pressure rollers (double-head pressure roller machine), three pressure rollers (three-head pressure roller machine) or four pressure rollers (four-head pressure roller machine) rotate or not.
6mm Animal Feed Pellet Machine Poultry Pellet Mill Machine 3-Head 220V 200kg/h Note: The machine not be used for wood chips. 1. Before using the machine, it is necessary to adjust the screw of the pressure roller to the appropriate position. The pressure roller and the pressure plate should be closely combined, and the three adjusting screws should be on the same horizontal plane. 2. Please fill the oil tank before using the machine. Do not idle the machine for more than 2 minutes. 3.Double-check the belt and the screws before operation. 4.Clean up the rest after use to prevent damage to the machine. 5.If the pressure roller cannot rotate normally, please tighten the screws that control the pressure roller first, and then try to power it on. If it still does not work, you can appropriately loosen the screws next to the pressure roller and then tighten them slightly again (without special tightening) 6.This machine only has a body without a pressure plate. Customers can purchase it separately if they need. We have 2MM, 3MM, 4MM, 5MM, 6MM, 8MM, 10MM, 12MM plate sizes for customers to choose. Product parameter: Standard pressure plate: 6MM Maximum output/h 200KG power: 4.5KW voltage: 220V Product body material: cast iron Standard pressure roller: Three head press roller Product size: 32.67*12.99*30.18in(83*33*76.5cm) Feature: This machine only has 6MM plates. If you need plates of other sizes,, please contact us. Item Number: 1*Chicken Feed Pellet Mill Machine 220V (239173) Shipping & Handling Details Default Shipping Cost or Free Shipping Information: ▲ Default shipping cost or free shipping service is only for the customers from Canada or the lower 48 United States by Canada Post, USPS or the UPS Ground. Customers from other areas or needs other shipping ways, please contact us. ▲ Buyers from Guam, Puerto Rico, Virgin Islands, American Samoa, Alaska, Hawaii, PO Boxes, APO/FPO addresses or other countries/areas, there will be extra shipping costs, please contact us for more detailed information. ▲ Please make sure your address is valid for both UPS and USPS services. Any costs incurred because of incorrect or undeliverable address should be undertaken by buyer. Handling Time: Shipping is usually made in 1-3 business days after payments cleared. Orders are processed from Monday-Friday; Not on the weekends & public holidays. Sales tax / Customs duties: Any sales taxes or Customs duties are not included. If came out, they must be undertaken by the buyer. Damage In Shipping: Email or call us First! We will work with you to get the case resolved in the fastest method. Return / Refund If you are not 100% happy with your purchase, please contact Us. Please don’t directly opened a request or case without informing us, or else, we will do some discounts on the warranty and other sales-services later on. Hope for your understanding. Returns & Exchanges ▲ All returns must be made within 14 days of delivery date. Items must be in new, unused condition, with all original materials included with the shipment. A partial refund may be applied for opened or damaged items, depending on the condition. ▲ Items returned under the buyer’s remorse: The return shipping fee must be covered by the buyer; The original shipping cost will also be deducted from the refund. 15% restocking fee of the items purchase price will be charged. ▲ Returns that are the result of our seller’s error: Buyer will receive a full refund of the item as well as shipping charges ▲ All returns require a RA (Return Authorization) number that will be given by our seller. Please contact with us at first for more details. Defective & Damaged Products ▲ If product was received damaged or not as described, please send us some pictures or videos, so we could well understand your problem, then solve them for you ASAP. Besides, it’s much helpful for us to claim with UPS, remind our related department to pay much more attention to packaging later on. Hope for your understanding. ▲ Replacement or refund of defective or damaged products can only be returned in exchange for the exact same product, or else, the purchase price will be refunded back to your original payment method. ▲ If an item is received damaged, customer service must be contacted within 7 days of receiving your item. All returns require a RA (Return Authorization) number as above. Warranty & Feedback ▲ 6 months’ warranty for the machines, not for the consumables. We stand behind our products all the item, so even if your warranty period has expired, you can still seek for service or technical support from us with low cost. ▲ Any warranty shipping cost to us is responsible by buyer. ▲ Any shipping cost to buyer is responsible by the seller. ▲ We committee to the customer satisfaction and want to bring you the best purchase experience. If there is any problems, please contact us ASAP. If not, please leave us a positive feedback as it’s very important for us. Thanks very much. 新建网页 1 On May 21, 2024 at 21:14:20 PDT, seller added the following information:
Output/h Maximum output 200KG (ideal state). When using, it should be noted that there should be no foreign matter such as stones and iron blocks in the raw materials. After the pellet machine has been working continuously for more than ten shifts, the pressure roller oil hole, the universal joint oil hole, and the linkage shaft oilhole need to be filled with high-temperature lubricating grease to make the pressure roller have good working performance and extended bearing life.
This machine is suitable for crushing all kinds of grass, corn, wheat, peanuts, beans and straw. The processed feed is more convenient for storage. Before starting the machine, it is necessary to check whether there are sundries in the machine.
When the machine is used, it should be noted that there should be no foreign matter such as stones and iron blocks in the raw materials. After the pellet machine has been working continuously for more than ten shifts, the pressure roller oil hole, the universal joint oil hole, and the linkage shaft oil hole need to be filled with high-temperature lubricating grease to make the pressure roller Good working performance and extended bearing life.
Draminski Hay & Silage High-Moisture Meter with Remote Probe Plus Temperature Display Great for Hay and SILAGE, Moisture Range 10-80%, Minimum, Maximum and Average Functions. Temperature Display in Degrees Fahrenheit LCD Digital Display with Large Numbers for Easy Reading Probe Length 22 Inches / 56 cm Uses One 9 Volt Battery 2 Year Warranty Advantages The most durable device for measuring hay and silage moisture available.LCD screen displays average, minimum and maximum moisture value.The device is equipped with temperature measurement feature.The probe is made of stainless steel which guarantees durability and resistance to corrosion. Ergonomically shaped handle helps to conduct measurements in tightly compressed bales. Extremely easy to use.Has an option to modify readings. The package includes: DRAMIŃSKI HMM moisture meter. Measuring probe with a connecting cableProtective cap to secure and protect the probe in transport1 x 9V 6F-22 type batteryUser manual