Item Tag: Carburetor

Carburetor 8N9510C-HD For Ford Tractor 2N 8N 9N Heavy Duty Marvel ScheblerItem Specification Condition: 100% Brand New and High Quality. Replacement Part Number: 8N9510C, 9N9510A, B3NN9510A, TSX241A, TSX241B, TSX241C, TSX33, 8N9510C-HD, 0-13876, 13876 8N9510C, 9N9510A, B3NN9510A, TSX241A,TSX241B Compatible Models: For 1942 1943 1944 1945 1946 1947 Ford 2N Tractor For 1947 1948 1949 1950 1951 1952 Ford 8N Tractor For 1939 1940 1941 1942 Ford 9N Tractor Measurement: Mounting Studs Measure ：57MM(Center To Center) Air Inlet Inner Diameter：33.5mm Air Inlet Outer Diamete：39.5mm Intake Side diameter：26.8mmPackage Included: Carburetor with fuel filter and gaskets as Pictured The installation steps for a carburetor can generally be followed in the order below: 1. Check the Carburetor and Accessories Before installation, check the carburetor and related components for any damage, wear, or contamination to ensure they are in good condition. 2. Cleaning Clean the surface where the carburetor will be installed, as well as the intake manifold, to ensure there is no dust or debris that could affect the proper functioning of the carburetor. 3. Remove the Old Carburetor Before removing the old carburetor, disconnect the power (if there is an electronic control system) and fuel lines, and turn off the engine. Detach the intake and exhaust hoses from the carburetor, which are typically located at the bottom or side of the carburetor. Remove the securing screws, usually Allen screws or flathead screws (use a specialized carburetor screwdriver). Carefully lift the carburetor to separate it from the engine, taking care not to damage it. 4. Install the New Carburetor Position the new carburetor in its original place, ensuring it is properly aligned with the intake manifold or intake port. Be sure the intake and exhaust ports are installed correctly (not reversed), and then tighten the securing screws. 5. Connect the Fuel Line Attach the fuel line to the fuel inlet of the carburetor, ensuring that the connection is tight to avoid fuel leakage. Check the fuel line for signs of aging or damage; if any is found, replace it. 6. Secure the Carburetor Use bolts to secure the carburetor to the intake manifold or the appropriate position, ensuring it is firmly in place without any wobbling. 7. Check the Electronic Control System (if applicable) If the carburetor has an electronic control system (such as an automatic throttle control), connect the cables or wires, ensuring all electrical connections are secure and correct. 8. Adjust the Carburetor Adjust the fuel/air mixture, idle speed, and other tuning screws according to the vehicle or equipment requirements to ensure smooth operation. 9. Check the Cylinders and Exhaust System After installing the carburetor, ensure there are no air leaks in the intake system, that the cylinders are functioning properly, and that the exhaust system is clear. 10. Test the Engine Open the throttle, start the engine, and observe the operation of the carburetor. Check for any unusual noise, fuel leakage, or stalling. Make fine adjustments if necessary. 11. Final Check Inspect all connection points, including the fuel lines, cables, and bolts, to ensure they are tightened properly and there are no loose connections or leaks. These steps are generally applicable to carburetor installations. Specific details should be referenced in the carburetor’s installation manual or the manufacturer’s instructions.PaymentDelivery detailsShipmentReturnContact usPaymentWe only accept PayPal and you can pay with your major credit card using PayPal.PayPal is the safest and most secure way for buyers and sellers to sell online and that is why we use it.Delivery detailsWe ship within 1-3 business day upon receipt of payment. Free Shipping from Kentucky , Texas or California US. Tracking information will be sent via email after your package ships.ShipmentWe ship within 1-3 business day upon receipt of payment. Free Shipping from Kentucky , Texas or California US. Tracking information will be sent via email after your package ships.ReturnReturn within 30 days after purchasing.Before return, please contact our customer service team via ebay message for return instructions. Unauthorized returns or used item will not be accepted.Please don’t open return request before contact us. For defective or damaged item, please contact us and provide as much problem details as possible, we will consider to waive return and ship replacement item or issue full refund to you directly after problem is confirmed.Contact usThis item have 3 months warranty. In the event the item should fail due to manufacturing defects during intended use, we will replace the part by free. We only warranty cost of item parts. Any installation or other fees are non-refundable. If you have any problems, please feel free to contact us anytime.BrandSVKCARCompatible Equipment Type8N9510C-HDModel Year1939-1952Model8N9510C, 9N9510A, B3NN9510A, TSX241A,TSX241BCompatible Equipment MakeFor Ford, For Marvel ScheblerCountry/Region of ManufactureChinaPart TypeCarburetorWarranty90 days